Changing channels is unavoidable if in near area another system is working on close frequency.

Every system has 8 of all 69 predetermined channels from the band, which are able to be changed by operator, using available buttons. Operator changes channels in the transmitter, Receiver tunes automatically to the selected channel. To change channels in transmitter, operator must follow instructions writen below.

-  turn transmitter off with the key

-  press the STOP button

-  attach supply to the transmitter (turn on the key-switch)

-  press button (f)  or turn joystick to  (f)  position

-  while pressing  (f)  press “START” (P2) button

-  transmitter will inform operator with sound and flashing green LED indicator, on which of 8 channels transmitter is operating. Quantity of sound signals (from 1 to 8) signalizes number of channel. To change the channel to next press the (+f,p)  button or push joystck to (+f,p) position. The alteration will be signalized by adequate number of sound- signals. Every pushing of (+f,p)  button causes in changing the channel to next. After reaching eighth channel, pushing (+f,p)  will cause in passing into the first channel and it will be indicated in single sound- signal.

-  after choosing adequate channel, pull out the STOP button- it causes saving chosen channel by transmitter.

- when all instructions are done it is possible to start operating the transmitter with START button on newly chosen channel.

Every system has possibility to change 3 levels of radiation power, which are able to be changed by operator, using available buttons. Operator changes power in the transmitter, Receiver tunes automatically to the selected channel. To change channels in transmitter following instructions must be done.

-  turn transmitter off with the key

-  press the STOP button

-  turn on supply to the transmitter

-  press button (p) or turn joystick to (p) position

-  while pressing (p) press “START” (P2) button

-  transmitter will inform operator with sound and flashing green LED indicator, on which of 3 levels of power transmitter is operating. Quantity of sound signals (from 1 to 3) signalizes number of level. Maximum power is 3 signals and it means 10mW. To change the level to the other press the (+f,p) button or push joystck to (+f,p) position. The alteration will be signalized by adequate number of sound- signals. Every pushing of (+f,p) button causes in changing the level to next. After reaching third level, pushing (+f,p) will cause passing into the first level and will be indicated with single sound- signal.

- after choosing adequate power, pull up the STOP button- it causes saving chosen level by transmitter.

- when all instructions are done it is possible to start operating the transmitter with START button on newly chosen level of power.

Changing channels is unavoidable if in near area another system is working on close frequency.

Every system has 8 of all 69 predetermined channels from the band, which are able to be changed by operator, using available buttons. Operator changes channels in the transmitter, Receiver tunes automatically to the selected channel. To change channels in transmitter, operator must follow instructions writen below.

-  turn transmitter off with the key

-  press the STOP button

-  attach supply to the transmitter (turn on the key-switch)

-  press button (f)  or turn joystick to (f)  position

-  while pressing  (f)  press “START” (P2) button

-  transmitter will inform operator with sound and flashing green LED indicator, on which of 8 channels transmitter is operating. Quantity of sound signals (from 1 to 8) signalizes number of channel. To change the channel to next press the (+f,p)  button or push joystck to (+f,p) position. The alteration will be signalized by adequate number of sound- signals. Every pushing of (+f,p)  button causes in changing the channel to next. After reaching eighth channel, pushing (+f,p)  will cause in passing into the first channel and it will be indicated in single sound- signal.

-  after choosing adequate channel, pull out the STOP button- it causes saving chosen channel by transmitter.

- when all instructions are done it is possible to start operating the transmitter with START button on newly chosen channel.

Every system has possibility to change 3 levels of radiation power, which are able to be changed by operator, using available buttons. Operator changes power in the transmitter, Receiver tunes automatically to the selected channel. To change channels in transmitter following instructions must be done.

-  turn transmitter off with the key

-  press the STOP button

-  turn on supply to the transmitter

-  press button  (p) or turn joystick to (p)  position

-  while pressing  (p)  press “START” (P2) button

-  transmitter will inform operator with sound and flashing green LED indicator, on which of 3 levels of power transmitter is operating. Quantity of sound signals (from 1 to 3) signalizes number of level. Maximum power is 3 signals and it means 10mW. To change the level to the other press the (+f,p)  button or push joystck to (+f,p) position. The alteration will be signalized by adequate number of sound- signals. Every pushing of (+f,p)  button causes in changing the level to next. After reaching third level, pushing (+f,p) will cause passing into the first level and will be indicated with single sound- signal.

-  after choosing adequate power , pull up the STOP button- it causes saving chosen level by transmitter.

- when all instructions are done it is possible to start operating the transmitter with START button on newly chosen level of power.

• power supply: batteries NiMH 1900 mAh, R6 type
• radiation power to 10 mW (regulated by operator)
• harmonic: <=65 dB
• modulation 5kHz
• mechanical switches
• temperature range from - 20⁰C to + 55⁰C
• IP65 housing

• power supply AC 230V, 42V, 48V, 24V
• power supply DC 24V, 12V
• the possibility of adapting the power supply
• outputs analog, current, CAN, RS232, RS485
• sensitiveness – 1uV
• maximal joint load 1A 24V DC, 3A 230V A
• lifetime : 1 milion operations or 10 years

• Turn off the transmitter with key.
• Turn the nut about 90 degrees contrary to clockwise.
• The spring will pull out partly batteries; leaning back the transmitter, remove all 2 batteries.
• Insert charged batteries, all in the same direction- due to the picture (batterie's “+” to the cover), than push the cover to press batteries.
• Press to the edging and turn clockwise about 90 degrees (to the edging) the nut protecting from the weather conditions. Due to sealing up function, the nut turns rather tightly.
• Turn on the transmitter and check up operating of system.